Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Moving Parts Come Out Sharp When All Pixels Are Exposed at the Same TimeCrack width in tenths of a millimeter: why you measure instead of guessingWith 15 Centimeters of Clearance to the Circuit Board, There Is Room for Both the Soldering Iron and Your Line of SightShiny metal surfaces can be measured once the reflections disappear and the entire surface is in focusReflections on the metal surface hide the scratch: how to see it with polarized light and a measurement functionInspect the solder joint on a screen right at the workstation, without a computer and without getting too closeAtt se in i röret i stället för att gissa: så sparar en inspektionskamera dagar av felsökningMeasure the scratch, edge or hole on site before the part is sent to the measuring roomMeasure under the microscope instead of next to it: get documentable measurements without losing your workspaceShiny metal surfaces hide defects: how to remove glare before you assess the surfaceVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Moving Parts Come Out Sharp When All Pixels Are Exposed at the Same TimeCrack width in tenths of a millimeter: why you measure instead of guessingWith 15 Centimeters of Clearance to the Circuit Board, There Is Room for Both the Soldering Iron and Your Line of SightShiny metal surfaces can be measured once the reflections disappear and the entire surface is in focusReflections on the metal surface hide the scratch: how to see it with polarized light and a measurement functionInspect the solder joint on a screen right at the workstation, without a computer and without getting too closeAtt se in i röret i stället för att gissa: så sparar en inspektionskamera dagar av felsökningMeasure the scratch, edge or hole on site before the part is sent to the measuring roomMeasure under the microscope instead of next to it: get documentable measurements without losing your workspaceShiny metal surfaces hide defects: how to remove glare before you assess the surface

Crack width in tenths of a millimeter: why you measure instead of guessing

Published 15 November 2026 at 10:29

Someone calls and says a crack has appeared in the floor, in a joint or in a casting. You go there, take a look and judge that it looks fairly thin. Three months later someone else thinks it looks wider, and nobody can show anything other than a memory of how it looked before. Without a measured value, it is impossible to determine whether the crack is growing, or to document it in a way that holds up.

Spricklupp, RL-B-10. Förstoring 10x

What a crack magnifier is

The RL-B-10 crack magnifier is a handheld measuring magnifier with 10x magnification. It has a graduated scale with 0.1 mm divisions, engraved in a matte chrome-plated brass plate. The scale is mounted at a 30-degree angle in the base of the magnifier. This gives good light entry and reduces reflections, so the scale can be read even on shiny surfaces.

The optics are apochromatic and distortion-free, built from an achromat and two single lenses. The field of view is 20 mm and the working distance is 10 mm. The magnifier can be focused using a sliding lens system. It measures 30 x 51 mm, weighs 55 grams and is supplied in a plastic case. The limit for the metal graduation is stated as approximately 40 µm.

The problem it solves

The magnifier replaces judging by eye with a measured value. You place it against the surface, focus and read the width directly against the scale. It is quick, requires neither power nor software, and gives you a number you can enter in an inspection report line or a maintenance system.

Three use cases

Building inspection. Technicians and appraisers use the magnifier to measure crack width in concrete. If you measure the same crack at intervals of a few months and note the date and location, you get documentation that shows whether the crack is stable or moving.

Metalworking. The magnifier is specifically intended for inspection in the metal industry. On milled, ground or cast parts, you can assess whether a line in the surface is a scratch or a crack, and how wide it is. The metal scale is preferable here to a glass scale.

Maintenance and service. During inspection rounds of machine parts, joints, welds and fixings, there is seldom time or space for a microscope. A magnifier that fits in your pocket means the check actually gets done, and gets done the same way every time.

Why it pays off

The price is under four thousand kronor, which is a fraction of what an unnecessary investigation or a wrongly dismissed finding can cost. A measured value lets you leave stable cracks alone and put measures in place where the width is actually increasing. It also saves time during inspections, since the result can be compared between people and between occasions, instead of depending on who happened to look.

Scales can be ordered separately as spare parts, so the magnifier can stay in service even after many years of use in the workshop and on the building site.

If you need a simple and traceable way to measure cracks in the field, the RL-B-10 is a reasonable first step.

Read more

More news

All news