Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Shiny Surfaces and Tight Workspaces: How to Get a Measurable Image Without GlareMoving Parts Come Out Sharp When All Pixels Are Exposed at the Same TimeCrack width in tenths of a millimeter: why you measure instead of guessingWith 15 Centimeters of Clearance to the Circuit Board, There Is Room for Both the Soldering Iron and Your Line of SightShiny metal surfaces can be measured once the reflections disappear and the entire surface is in focusReflections on the metal surface hide the scratch: how to see it with polarized light and a measurement functionInspect the solder joint on a screen right at the workstation, without a computer and without getting too closeAtt se in i röret i stället för att gissa: så sparar en inspektionskamera dagar av felsökningMeasure the scratch, edge or hole on site before the part is sent to the measuring roomMeasure under the microscope instead of next to it: get documentable measurements without losing your workspaceVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Shiny Surfaces and Tight Workspaces: How to Get a Measurable Image Without GlareMoving Parts Come Out Sharp When All Pixels Are Exposed at the Same TimeCrack width in tenths of a millimeter: why you measure instead of guessingWith 15 Centimeters of Clearance to the Circuit Board, There Is Room for Both the Soldering Iron and Your Line of SightShiny metal surfaces can be measured once the reflections disappear and the entire surface is in focusReflections on the metal surface hide the scratch: how to see it with polarized light and a measurement functionInspect the solder joint on a screen right at the workstation, without a computer and without getting too closeAtt se in i röret i stället för att gissa: så sparar en inspektionskamera dagar av felsökningMeasure the scratch, edge or hole on site before the part is sent to the measuring roomMeasure under the microscope instead of next to it: get documentable measurements without losing your workspace

Measure what you see: how to document surface defects and solder joints with a handheld digital microscope

Published 13 October 2026 at 04:44

It happens in most workshops and inspection rooms. Someone points at a scratch in a sealing surface or a suspect solder joint and says it is too deep. Someone else says it is acceptable. With an ordinary magnifier it becomes a judgment call, not a measured value, and when the complaint arrives months later there is nothing to show.

Dino-Lite Premier, 1,3 Mpixels, mätfunktion, metall

What it is

The Dino-Lite AM4013MT is a handheld digital microscope in an aluminium housing. It has a 1.3 megapixel CMOS sensor and up to 200x optical magnification. It connects to a computer via USB and shows the image live on the screen. The eight white LEDs in the ring can be switched on and off, and an IR filter gives natural colour reproduction. The software DinoCapture 2.0 for Windows or DinoXcope for MacOS is included and makes calibrated measurements directly on the image.

What problem it solves

The microscope replaces judgment with a value. You can measure a crack width, the distance between pins, a chip width or a corrosion spot, and save the image with the dimension drawn in. In addition, several people can view the same image on the screen at the same time, which makes the discussion about what is acceptable much shorter.

When and why it is used

The instrument is suited to situations where the detail is too small for the eye but the location is too awkward for a stationary microscope. Because it is held in the hand, you can take it to the machine, the assembly bench or the returns box. Always measure against a calibrated reference at the same magnification before trusting the numbers, and note the magnification in the report.

Three areas of use

Machine shop. Check for edge chipping on inserts, burr formation on drilled holes and wear on sealing surfaces. A measurement of the wear before and after a production run shows when the tool actually needs replacing, not just when someone thinks it looks worn.

Electronics. Inspect solder joints, connectors and conductor tracks. You can see whether a joint is cold or bridged and measure the distance between leads on fine-pitch components. The image follows the board during troubleshooting or supplier discussions.

Food and installation. Inspect weld seams in pipes, damage to sealing strips and worn edges on cutting tools in the production line. Where hygiene and tightness are critical, a saved image provides documentation for your self-inspection program.

Why it pays off

The cost is easiest to compare with the alternative. A stationary measuring microscope requires the part to leave the site, and an external lab costs time and money for every question. With a handheld instrument you carry out the check in two minutes at the workplace. Each saved image is also documentation that can stop an unnecessary discussion with a customer or supplier, and it can determine who bears the cost of a rejection. Just a few avoided misjudgments per year are usually enough to cover the purchase.

If you want a closer look at specifications, magnification range and software, everything is on the product page for the Dino-Lite AM4013MT.

Read more

More news

All news