Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Moving Parts Come Out Sharp When All Pixels Are Exposed at the Same TimeCrack width in tenths of a millimeter: why you measure instead of guessingWith 15 Centimeters of Clearance to the Circuit Board, There Is Room for Both the Soldering Iron and Your Line of SightShiny metal surfaces can be measured once the reflections disappear and the entire surface is in focusReflections on the metal surface hide the scratch: how to see it with polarized light and a measurement functionInspect the solder joint on a screen right at the workstation, without a computer and without getting too closeAtt se in i röret i stället för att gissa: så sparar en inspektionskamera dagar av felsökningMeasure the scratch, edge or hole on site before the part is sent to the measuring roomMeasure under the microscope instead of next to it: get documentable measurements without losing your workspaceShiny metal surfaces hide defects: how to remove glare before you assess the surfaceVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Moving Parts Come Out Sharp When All Pixels Are Exposed at the Same TimeCrack width in tenths of a millimeter: why you measure instead of guessingWith 15 Centimeters of Clearance to the Circuit Board, There Is Room for Both the Soldering Iron and Your Line of SightShiny metal surfaces can be measured once the reflections disappear and the entire surface is in focusReflections on the metal surface hide the scratch: how to see it with polarized light and a measurement functionInspect the solder joint on a screen right at the workstation, without a computer and without getting too closeAtt se in i röret i stället för att gissa: så sparar en inspektionskamera dagar av felsökningMeasure the scratch, edge or hole on site before the part is sent to the measuring roomMeasure under the microscope instead of next to it: get documentable measurements without losing your workspaceShiny metal surfaces hide defects: how to remove glare before you assess the surface

Measure the scratch, edge or hole on site before the part is sent to the measuring room

Published 17 October 2026 at 02:25

An operator stops the machine and wonders whether the wear on the tool edge is five or ten micrometres. The eye isn’t enough, the vernier caliper can’t reach, and the measuring room is in another building. The decision often ends up being an estimate, and an estimate is expensive if it turns out to be wrong.

Mätmikroskop, Peak Lupe 2034-serien. Förstoring 150x med skala 0,005mm

What it is

The Peak Lupe 2034 is a portable measuring microscope. The optics consist of an objective and a 10x eyepiece with a reticle scale in glass. This version provides 150x magnification and a scale division of 0.005 mm. The same series is available with magnifications from 20x to 300x, and the objectives are easily screwed on and off.

The microscope stands on a clear acrylic base. You can see the object from all sides and find the measuring point without searching. Place it over the area, focus and read the scale. The image is inverted because of the short light path, which you get used to fairly quickly.

What problems it solves

It bridges the gap between a magnifier and a laboratory microscope. An ordinary magnifier gives magnification but no measurable scale. A stationary measuring microscope gives numbers, but requires the part to be moved. Here you measure the length, thickness, height and depth of objects with different levels at the place where they sit. The scale is located in the focal plane of the eyepiece, so dust cannot get into it.

When and why it is used

Use it when the dimension is too small for a vernier caliper but the decision can’t wait. Adjust the eyepiece to your own eye with the adjustment ring, and the reading will be consistent between different people.

One thing is worth remembering. The scale is tied to the magnification. If you change the objective, order it together with the right eyepiece and scale, otherwise the reading will be wrong.

Three use cases

Engineering workshops: Checking edge wear, chamfer width and cracks on tools and parts, without removing the part from the machine.

Electronics: Width of conductors and solder pads, distance between components and diameter of holes in circuit boards.

Food production: Checking mesh size in sieves and filters as well as wear on cutting parts, where a deviation could otherwise lead to process disruption or foreign objects in the product.

The economics

The cost is small compared with a stationary measuring microscope, and the biggest gain is time. Every time a measurement can be made at the machine instead of being sent away, you save downtime and waiting. You also detect wear and deviations earlier, when corrective action is still cheap. If you still need to change the magnification, replacement lenses are available, so the same base unit can cover several tasks.

If you need to measure small details on site, take a look at the Peak Lupe 2034 and choose the magnification that suits your tolerances.

Read more

More news

All news