Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Glossy Surfaces and Incorrect Magnification: How to Get Reliable Measurements Under the MicroscopeShiny Surfaces and Tight Workspaces: How to Get a Measurable Image Without GlareMoving Parts Come Out Sharp When All Pixels Are Exposed at the Same TimeCrack width in tenths of a millimeter: why you measure instead of guessingWith 15 Centimeters of Clearance to the Circuit Board, There Is Room for Both the Soldering Iron and Your Line of SightShiny metal surfaces can be measured once the reflections disappear and the entire surface is in focusReflections on the metal surface hide the scratch: how to see it with polarized light and a measurement functionInspect the solder joint on a screen right at the workstation, without a computer and without getting too closeAtt se in i röret i stället för att gissa: så sparar en inspektionskamera dagar av felsökningMeasure the scratch, edge or hole on site before the part is sent to the measuring roomVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Glossy Surfaces and Incorrect Magnification: How to Get Reliable Measurements Under the MicroscopeShiny Surfaces and Tight Workspaces: How to Get a Measurable Image Without GlareMoving Parts Come Out Sharp When All Pixels Are Exposed at the Same TimeCrack width in tenths of a millimeter: why you measure instead of guessingWith 15 Centimeters of Clearance to the Circuit Board, There Is Room for Both the Soldering Iron and Your Line of SightShiny metal surfaces can be measured once the reflections disappear and the entire surface is in focusReflections on the metal surface hide the scratch: how to see it with polarized light and a measurement functionInspect the solder joint on a screen right at the workstation, without a computer and without getting too closeAtt se in i röret i stället för att gissa: så sparar en inspektionskamera dagar av felsökningMeasure the scratch, edge or hole on site before the part is sent to the measuring room

Glossy Surfaces and Incorrect Magnification: How to Get Reliable Measurements Under the Microscope

Published 18 November 2026 at 12:30

You lean over a solder joint, a cutting insert or a cast part and mainly see a white glare where the defect should be visible. By the time the image is finally sharp, someone has turned the magnification, and the measurement you read in the software is no longer correct. These are two common reasons why microscope inspection takes longer than it should and produces unreliable results.

Dino-Lite EDGE 5 Mpixels, långt fokusavstånd, mätfunktion, automatisk förstoringsavläsning, FLC, polarisator, metall

What it is

The Dino-Lite EDGE AM7515MZTL is a digital USB microscope with a 5-megapixel sensor and magnification from 10 to 140x. It belongs to the long working distance (LWD) series, which provides more space between the objective and the object. The housing is made of aluminum, and the microscope has a built-in polarizer, flexible light control (FLC), and calibration and measurement functions in the software. The front caps are replaceable.

What problems it solves

The polarizer reduces glare from metal, plastic, glass and electronics, so that surface structure and edges are visible instead of reflections. With flexible light control, you can direct the illumination from different directions and bring out scratches, burrs or cracks. Automatic magnification reading (AMR) registers which magnification is set and transfers it to the measurement software. This means nobody has to type in or guess the scale, and the risk of misreading drops noticeably when measurements are made often.

When and why it is used

A long working distance is needed when you want to work under the microscope, for example with tweezers, a soldering iron or small hand tools. It is also suitable for bulky or fragile objects that must not be touched. A stand is recommended at higher magnifications, since a handheld image becomes unsteady.

Three areas of use

Electronics: When repairing and reworking circuit boards, you can check solder joints, short circuits and component placement without reflections from shiny solder getting in the way. The same image can be documented for the quality report.

Machine shops and manufacturing: Wear on cutting edges, surface finish after milling and burrs on drilled holes can be assessed on the screen. With calibrated measurement, you can state how large the wear is, not just that it exists.

Quality control: Plastic and metal parts with a glossy surface are often inspected against a reference. When the image, magnification and measurements are saved together, it is possible to compare batches over time and show a customer or auditor what was intended.

Why it pays off

The time is seldom spent on the inspection itself, but on adjusting the light again and again, reading the scale and taking new images. The polarizer and AMR remove two of the most common reasons for retakes. The shared image on the screen also means that a colleague can assess the same part without taking your place at the eyepiece. And a faulty assessment of a part that goes on to assembly or to the customer costs more than a microscope in this class.

Do you need to measure and document surfaces that are difficult to see properly? Read more about the Dino-Lite EDGE with polarizer and automatic magnification reading.

Read more

More news

All news